The modification I mentioned is the last example posted here:
http://www.paia.com/ProdArticles/tmpmod.htmHowever, it is for the 9407 Tube MicPreAmp rather than 9305 TubeHead, and tapping DC from the negative supply, but it could have been a reason for the extra current flow if it had been in place (and on the positive supply).
If you have the 12VAC to the tube filaments as is normal, then please disregard my mention of DC supply to the filaments.
The voltage to pin 8 of the op-amps should be about the same as the voltage to pin 4 of the op-amps.
So, there must be more current flow on the positive side, resulting in less voltage.
The 4049 IC has the positive DC voltage to it, but not from the op-amp side of R1. Instead, it is from the D1 and C1 side and labeled Vcc. The voltage is more here and this is to get the most from the voltage multiplier circuit section including the 4049.
If this 4049 feels warm to hot when touching it, it might have failed (accidental short circuit???). If so, it could be using more of the positive DC supply power than is normal, resulting in lower than normal voltage o the op-amp side of R1.
If the 4049 is cool to the touch, then it is probably doing its job of switching voltage on and off to the following diode and capacitor voltage multiplying (x3) section. For the 12V to pin 1, the voltage switching will be 0 - 12 and DC measurements of C8, then C9, and then C10 should show 12V, 24V, and 32V (not the 45V on the schematic, but OK).
The 6V you report on the 4049 output pins 2, 4, and 6 make it likely the IC is operating and switching on/off at about 40KHz.
So, an abnormal load on the op-amp output might be post-audio oscillation occurring, or, a shorted shielded cable to an output connector with the internal wire touching the grounded shield wire.
This could occur from some trouble on the board or wiring such as soldering or other cause for a short- or open-circuit.
If you can email photos of the top and bottom sides of the board, and control/connector wiring I might be able to spot trouble and reply with advice.
And, thanks to: translate.google.com/
Die Modifikation I erwähnt ist das letzte Beispiel hier gepostet:
http://www.paia.com/ProdArticles/tmpmod.htmJedoch ist es für den Schlauch Mikrofon-Vorverstärker 9407 anstatt 9305 Röntgenstrahler und Klopfen DC von der negativen Versorgungs, aber es könnte ein Grund für die zusätzliche Stromfluss, wenn es an Ort und Stelle (und auf den positiven Versorgungs) gewesen.
Wenn Sie die 12VAC zur Rohr Filamente als normal ist, dann ignorieren Sie bitte meine Erwähnung von Gleichstromversorgung zu den Filamenten.
Die Spannung an Pin 8 der Op-Amps sollten etwa die gleiche wie die Spannung an Pin 4 der Operationsverstärker sein.
So muss es mehr Stromfluss auf der positiven Seite zu sein, was zu einer geringeren Spannung.
4049 IC hat die positive Gleichspannung an, aber nicht von dem op-amp Seite R1. Vielmehr ist es aus der D1 und C1 Seite und markiertem Vcc. Die Spannung ist hier mehr, und das ist, um das Beste aus der Spannungsvervielfacherschaltung Schnitt einschließlich der 4049 zu bekommen.
Wenn dies 4049 fühlt sich warm bis heiß, wenn es zu berühren, könnte es versäumt haben (versehentlichen Kurzschluss ???). Wenn ja, könnte es sein, mit mehr von der positiven Gleichstromversorgungsleistung als normal, was niedriger als normal Spannung o des Operationsverstärkers Seite R1.
Wenn die 4049 ist kühl anfühlt, dann ist es wahrscheinlich, seine Aufgabe der Schaltspannung ein und aus, um folgenden Abschnitt Diode und Kondensatorspannung Multiplikations (x3). 12 und DC-Messungen von C8, dann C9, C10 und dann sollte zeigen, 12V, 24V und 32V (nicht die 45V auf der schematischen, aber OK) - Für die 12 V an Pin 1 wird die Spannungsschalt 0 sein.
Die 6V Sie auf den 4049 Ausgangs-Pins 2, 4 zu melden, und 6 machen es wahrscheinlich, das IC in Betrieb und Ein- / Ausschalten bei etwa 40 kHz.
So, eine anormale Belastung auf den Operationsverstärker-Ausgang könnte post-Audioschwingungs auftritt, oder ein Kurzschluss abgeschirmten Kabels an einem Ausgangsanschluss mit dem inneren Draht Berühren des geerdeten Schirmdraht.
Dies könnte einige Schwierigkeiten auf der Platine oder Verdrahtungs auftreten, wie Löten oder andere Ursache für einen Kurz- oder Leerlauf.
Wenn Sie sich die Fotos von der Ober- und Unterseite der Platine, und die Steuerung / Steckerverdrahtung eine E-Mail, ich könnte Probleme erkennen und antworten mit Beratung.